The Skip Gram "G-Styk"

Listed below is an extensive and hopefully complete parts list of items you will need to complete the build:


1 - E-Flite Power 60 Brushless Outrunner Motor, 400Kv, 1700 watts

1 - 75 amp, 6 or more cell Electronic Speed Controller(ESC) - We went with the Castle Creations Ice HV100 ESC, rated for 8S Lipos and 100amps continuous output

1 - ESC Programming cable

1 - Set of three Male/Female 4mm Bullet Connectors

1 - Pack of Heat Shrink Tubing

12 - Small Tie Wraps

1 - 13x8, 13x10, 14x6, 14x8 or 14x10 APC Electric Propeller

1 - Ultra Deans Male Connector

1 - High Strand, Low Loss, 12" length, 12ga Black Silicon Wire

1 - High Strand, Low Loss, 12" length, 12ga Red Silicon Wire

1 - Ultra Deans Heavy Duty Y Connector (2 male to 1 female)

1 - Anti Spark Assembly

4 - 3mm Hex Motor Mount Mounting Bolts

4 - 3mm Flat Washers

4 - 3mm Lock Washers

4 - 3mm Blind Nuts

4 - 4-40 x 3/4" Hex Mounting Bolts (for ESC mounting)

8 - 4-40 Flat Washers (for ESC mounting)

4 - 4x40 NyLoc Self Locking Nuts (for ESC mounting)

1 - Velcro w/ Heavy Duty Adhesive Backing Set, 2" x 24"

1 - Velcro Strapping, 36" Length

1 - Aluminum Front Landing Gear

4 - 4-40 x 1" Hex Mounting Bolts (for Landing Gear)

4 - 4-40 Lock Washers (for Landing Gear)

4 - 4-40 Flat Washers (for Landing Gear)

4 - 4-40 Blind Nuts (for Landing Gear)

2 - 4-40 x 1" Button Head Screws (for Top Hatch Cover)

1 - Dubro Quick Switch Mount Assembly

1 - 1/8" Plywood Fabricated Power Swtich/Charging Jack Plate

1 - 1/8" Plywood Fabricated Aileron Jack Plate

1 - 1/8" Plywood Fabricated Receiver Battery Box

5 - Sullivan 4x40 Heavy Duty Clevis

4 - 4-40 Nuts

5 - 4-40 x 12" Long Threaded Pushrods

5 - 4-40 PushRod Retainers

5 - Heavy Duty Control Horns w/ Screws

2 - 2x56 x 1" Hex Bolts

2 - 2x56 Flat Washers

2 - 2x56 Nyloc Self Locking Nuts

1 - Tailwheel Wire Assembly 1/8" diameter

1 - 5/32" Wheel Collar

1 - 5/32" OD Brass Tube

1 - 6x32 x 4" AllThread Rod

1 - Large EZ-Adjust Nylon Horn Bracket

1 - 1/8" ID Brass Tube

1 - 1/8" Wheel Collar

1 - 1/8" Flat Washers

1 - 1/8" Tail Wheel

2 - 2 3/4" Landing Gear Wheels (Mains)

2 - 8-32 x 1 1/2" Wheel Bolts (Mains)

4 - 8-32 Flat Washers (Mains)

2 - 8-32 Nuts (Mains)

2 - 8-32 Nyloc Self Locking Nuts (Mains)

1 - 30" x 24" Piece of White Monokote for Hinges

1 - Four or More Channel R/C Radio Transmitter, 2.4Ghz Preffered

1 - Four or More Channel R/C Radio Full Range Receiver

4 - Heavy Duty Servos (Futaba S9202 or equivalent)

4 - Servo Mounting Screw Set

4 - 36" Servo Extension Wires

1 - 12" Aileron Wire Extension

1 - Receiver Switch

2 - Futaba J Connector Jack Mounts (1 for Aileron Extension, 1 for Receiver Battery Charging)

1 - Sheet of Receiver Foam Padding

1 - Receiver Battery (4.8v or 6v)

1 - Sheet Receiver Battery Foam Padding

1 - Roll of Each Color Monokote/Ultracoat that you choose, Minimum 2-3 Six Foot Rolls

This Website and all documents herin are Copyright © 2012 www.scalerocketry.com - All rights reserved.